METRATESTER 5-3P Prüfkoffer DIN VDE 0701 und 0702
Article number: 35202
Listed in category: Measurement / Wire and Cables > METRATESTER 5-3P Prüfkoffer DIN VDE 0701 und 0702 from brakensiek.de
METRATESTER 5-3P test case with DIN VDE 0701 and 0702
New
- For testing single and three phase units according to DIN VDE 0701: 2000 and 0702: 2004
- With extensive facilities to CEE 16 connectors
- Including connection set for optional operation of the test panel
to earthed or 5-pin power outlet CEE16 A
[Link] www.elektrocad.de/SOFTWARE/e-manager/Leitfaden_0701_2.pdf [/ link] Here's a quick guide to the DIN VDE standards [/ link description]
equipped with a 5-Einbauprüfgerät METRATESTER FE:
- With visual and audible notification threshold
- Residual current measurement according to DIN VDE 0701/0702
comfortable examination by:
- Switch "POWER VDE" without changing the test specimens in
the types of tests according to DIN VDE with or without mains power.
- Phase Selector L1/L2/L3 for measuring current and voltage
- Phase reverse switch for mains voltage
- Display of all readings on the LCD screen of the tester
- Secure protection conductor according to DIN VDE 0404
(Separation of the mains earth conductor of the test doses)
- Compact, sturdy and lockable saving size
Application
The portable test kit for measuring and checking of incoming and
three-phase electrical appliances and extension cords
determined. This was in accordance with the guidelines of the ZVEH and
VDEW for workshop equipment from electrical installers
equipped with built-in test equipment.
The earth is "right" measured according to DIN VDE 0104.
With the test case, the following variables are examined:
- Protective conductor resistance
- Insulation resistance (L1/L2/L3/N short-circuited to PE)
- Equivalent Leakage
- Protective conductor current difference after the current method
(At one and three-phase DUTs)
- Touch-leakage current on specimens of the class II
- Mains voltage L1/L2/L3 to N
- Load current in L1/L2/L3
- Examine the supply according to DIN VDE 0701 part 240
- Continuity testing with low voltage
on indicator light
- Testing of extension cables in connection with the accessory VL2
Display Functions
All measured values are to a large digital display easy to read
issued. In addition, limits are exceeded
visually and in some cases acoustically.
Contact surface for finger contact
Via a contact surface for finger contact, the protective conductor potential to be checked. The PE signal lamp lights up if the contact surface and the protective conductor of the mains plug is a potential difference of more than 100 volts.
Safety equipment
- Tester: An overload protection (thermal) to 253 V in all areas (except 16 A). The test is to eliminate the overload once again operational. The high temperature is displayed on the LCD. The PE signal lamp indicates whether voltage is applied to the protective earth conductor.
- Test case: RCCB 4 pole 30 mA to the effective
Test power sockets and the sockets of the security
Test panel, emergency stop master switch with undervoltage release
connected in the 0 position.
New
- For testing single and three phase units according to DIN VDE 0701: 2000 and 0702: 2004
- With extensive facilities to CEE 16 connectors
- Including connection set for optional operation of the test panel
to earthed or 5-pin power outlet CEE16 A
[Link] www.elektrocad.de/SOFTWARE/e-manager/Leitfaden_0701_2.pdf [/ link] Here's a quick guide to the DIN VDE standards [/ link description]
equipped with a 5-Einbauprüfgerät METRATESTER FE:
- With visual and audible notification threshold
- Residual current measurement according to DIN VDE 0701/0702
comfortable examination by:
- Switch "POWER VDE" without changing the test specimens in
the types of tests according to DIN VDE with or without mains power.
- Phase Selector L1/L2/L3 for measuring current and voltage
- Phase reverse switch for mains voltage
- Display of all readings on the LCD screen of the tester
- Secure protection conductor according to DIN VDE 0404
(Separation of the mains earth conductor of the test doses)
- Compact, sturdy and lockable saving size
Application
The portable test kit for measuring and checking of incoming and
three-phase electrical appliances and extension cords
determined. This was in accordance with the guidelines of the ZVEH and
VDEW for workshop equipment from electrical installers
equipped with built-in test equipment.
The earth is "right" measured according to DIN VDE 0104.
With the test case, the following variables are examined:
- Protective conductor resistance
- Insulation resistance (L1/L2/L3/N short-circuited to PE)
- Equivalent Leakage
- Protective conductor current difference after the current method
(At one and three-phase DUTs)
- Touch-leakage current on specimens of the class II
- Mains voltage L1/L2/L3 to N
- Load current in L1/L2/L3
- Examine the supply according to DIN VDE 0701 part 240
- Continuity testing with low voltage
on indicator light
- Testing of extension cables in connection with the accessory VL2
Display Functions
All measured values are to a large digital display easy to read
issued. In addition, limits are exceeded
visually and in some cases acoustically.
Contact surface for finger contact
Via a contact surface for finger contact, the protective conductor potential to be checked. The PE signal lamp lights up if the contact surface and the protective conductor of the mains plug is a potential difference of more than 100 volts.
Safety equipment
- Tester: An overload protection (thermal) to 253 V in all areas (except 16 A). The test is to eliminate the overload once again operational. The high temperature is displayed on the LCD. The PE signal lamp indicates whether voltage is applied to the protective earth conductor.
- Test case: RCCB 4 pole 30 mA to the effective
Test power sockets and the sockets of the security
Test panel, emergency stop master switch with undervoltage release
connected in the 0 position.
Contact:
Your contact person: Tim Brakensiek
new products
last update:
22.05.2012
